how to reset mass air flow sensor nissan sentra

Remove the sensor from the housing. The sensor has to be.

How To Clean A Maf Sensor 2013 2019 Nissan Sentra Youtube

Turn ignition switch OFF.

. Restart engine and let it idle for at least 5 seconds. If your Nissan Sentra MAF Sensor spits out a reading at the signal wire thats outside of these specifications replace your mass air flow sensor. Replacing a bad MAF sensor can make your Sentra feel like a new vehicle.

Pull out the air. Up to 20 cash back Here is the tsb on replacing the Mass Air flow sensor. Dont know if this works the same for every vehicle tho.

CLEAR THE SELF-LEARNING DATA the manual SELF-LEARNING CONT procedure 1. Use a scan tool to reset your Nissan ECU and clear your trouble code. Now that you know when to reset the mass air flow sensor lets show how you can do it.

Allow the MAF sensor to dry and reinstall. Remove the air filter element. Locate the MAF sensor next to the engine air filter housing.

Clean the Sensor Now that youve removed your Sentras MAF sensor its time to clean it. Once you remove the large air vacuum hose you are now free to loosen the clamps on your intake piping. Before replacing the Mass Air Flow MAF sensor try replacing the air filter and cleaning the MAF sensor with low compress air or MAF sensor cleaner.

Stop engine and reconnect mass air flow sensor harness connector. Start engine and warm it up to normal operating temperature. I have a 2011 nissan sentra 20 kept getting mass air flow codes cleaned it a few times finally got an original nissan sensor cleared the codes but found one to be a permanent code which the computer ims are supposed to have a certain set of steps to fix the parameters but now after it was running great im getting a putt putt putt out the tailpipe like a cylinder isnt.

You only have to reprogram the computer if necessary. You are not scrubbing anything. Remove the two screws that hold the MAF sensor secure and remove the MAF sensor.

If you have a low MAF sensor trouble code this is where most of your low voltage issues will arise. Found in section DTC P0133 P0153 AF SENSOR 1 from page EC-265 5. As mentioned before therere two ways you can do it.

Anyways I ordered the part from eBay 25 and the car does not jerk. If the P0101 code is set and there are no. Yank out that old faulty mass air flow sensor and replace it with a new unit and you are ready to rock and roll.

Restart engine and let it idle for at least 5 seconds. About a dozen small bursts will be all that you need. Turn off the engine and let it cool down if youve been driving.

My car was jerking when pressing the gas pedal too much oxygen and I found the problem to be the Mass Air Flow sensor after doing some research. Make sure DTC P0102 is displayed. Find the location of the MAF sensor in your Sentra it will be somewhere between the air filter box and the throttle body.

Now when you have the intake piping removed you can undo the two bolts that secure the Sentra MAF to your Nissan air box. A basic instructional video on how to clean a mass air flow MAF sensor for a vehicle. Specifically this is for the 2013-2019 Nissan Sentra with the MRA8DE.

There is a factory service bulletin for the 2011-2012 Nissan Sentra. Lifted from X forums. Resetting the Mass Air Flow Sensor by Idling the Engine.

However when idling when first starting the car or when I am at a redlight it keeps jerking even when I am not pressing the gas. Unplug the electrical connector. Here is the instructions.

Then vacuum out all dustdirtdebris found inside both halves of the air filter housing. Disconnect mass air flow sensor harness connector. Reset code and drive vehicle.

Spray 8 to 12 spurts of MAF sensor cleaner on the exposed plate. Nissans mass airflow sensor sends a voltage to the. Youll need the MAF cleaner.

Remove the connector with the harness of the sensor. Let the chemicals do their job. Erase the DTC memory.

Disconnect mass air flow sensor harness connector. If the code comes back it may be necessary to replace the MAF sensor. Another option would be to go to your local auto parts store and buy a special mass airflow sensor cleaner and spray it onto your sensor but as stated before this is more expensiveDry and Reinstall the SensorAfter cleaning your mass airflow sensor with either the cleaner or rubbing alcohol let it sit generally for 20 minutes or more.

How to Reset the Mass Air Flow Sensor. Unplug the mass airflow sensor electrical connector. Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air dry for an hour or until completely dry.

Nissan Sentra Mass Air Flow Sensor Replacement Youtube